Results 1 to 5 of 5

Thread: Resonant SMPS using L6599

  1. #1
    diysmps Member* res_smps's Avatar
    Join Date
    Oct 2012
    Location
    bandung, indonesia
    Posts
    68

    Resonant SMPS using L6599

    Dear friends,

    I want to share my experience of making renonant smps using the L6599 chip.
    Please check the following pdf file L6599 resonan smps by res.pdf,

    apologize if the language is not good.

    Suggestions and critics are welcome.

    Thank you

  2. #2
    .... Silvio's Avatar
    Join Date
    Apr 2015
    Location
    Malta
    Posts
    705
    Blog Entries
    9
    Hi Res, The circuit looks promising at a first glance, from what I have read so far these tend to be a bit sensitive and usually they are used for a constant load. I do not know what are your intentions for this smps being either for learning purposes or maybe to use it somewhere. I have never built one myself but I have seen some lectures on youtube by Sam Ben Yakovv. This man is a professor in a university teaching students. I suggest you follow some of these videos and learn the Math behind this topology.

    As you may well know there are quite some types being in soft switching, Zero voltage switching or zero current switching. The task is to keep the smps at below or above resonance depending on the load requirements. This feature implies having a variable frequency controller that can sense the load current and adjusting the frequency to maintain the load current.

    Well I wish you well and good luck in your experiments and hope that you succeed.

    Regards Silvio

  3. #3
    diysmps Member* res_smps's Avatar
    Join Date
    Oct 2012
    Location
    bandung, indonesia
    Posts
    68
    Quote Originally Posted by Silvio View Post
    I have seen some lectures on youtube by Sam Ben Yakovv. This man is a professor in a university teaching students. I suggest you follow some of these videos and learn the Math behind this topology.
    I will try to search on youtube, thank you

    Because I was busy in my work in another field,
    for now I don't have a purpose why I make smps (I have no financial goal), I make it just because I like electronics

    I designed a smps with symmetrical output so that it can also be used for audio amplifiers especially for friends here

    Actually I can do mathematical calculations, from what I learned, the calculation of the infineon AN-1160 is easier for manual calculations rather than appnote from ST.
    attached L6599 excel spreadsheets for easy way.

    I tried to explain in my writing how to make transformer construction easy for DIY because in my opinion this is one of the difficult parts of making a resonant converter

    I've tried regulated and non regulated smps with the L6599 (and UCC25600) chip

    test load (i can not test in a long time because nikelin wire burning my table)
    https://www.youtube.com/watch?v=umJtKTdcC6E

    1000W version test
    https://www.youtube.com/watch?v=ksnf1ewgrAw

    over load test (voltage drop when overload)
    https://www.youtube.com/watch?v=-gEKRWsvgEs

    over current protection test by shorting output (smps shutdown, non-latching)
    https://www.youtube.com/watch?v=FSfd46yhywc

    sinusoidal voltage at Cr
    https://www.youtube.com/watch?v=y42T_Fw6fCs
    Attached Files Attached Files
    Last edited by res_smps; 05-15-2019 at 09:19 AM.

  4. #4
    @Res_SMPS


    I would appreciate your help if you can give me transformer turns ratio for +-22VDC output & the TL431 regulator resistors values, I am facing some challenges


    Thanks
    www.diysmps.com & www.Micro-Audio.com

  5. #5
    diysmps Member* res_smps's Avatar
    Join Date
    Oct 2012
    Location
    bandung, indonesia
    Posts
    68
    Dear Microsim,

    I tried to answer even though I myself was still learning
    from the appplication note AN2450, the turn ratio is not the physical turn ratio n=N1/N2
    but turn ratio n = 0.5 x Vdc(nom)/Vout
    for 220V mains n = 220*1.4*0.5/22 = 7
    is this what you mean?

    tl431 part.jpg
    for TL431 I honestly don't really understand too
    for example I choose 1K2 for R1 ( I don't know what preferable value range)
    vref = 2.5V
    R2 = R1(Vout/vref-1)
    for R1 I used fixed resistor+trimpot
    Vout+-22V = 44V (from positif rail to negatif)
    R1 = 1.2K(44/2.5-1) approx 19.92K

    for R-C compensation I just tried from the example schematic, I have not understood

    and make sure more than 1mA current passing trough TL431

    I use the TL431 circuit like in page 6 from iraudps3
    Attached Files Attached Files

Similar Threads

  1. Resonant power supply
    By maxente in forum diysmps
    Replies: 9
    Last Post: 05-10-2017, 08:24 PM
  2. Phase shifted pwm resonant h-bridge supply !
    By smps_fan in forum Power Supplies
    Replies: 59
    Last Post: 03-11-2017, 06:26 AM
  3. Replies: 0
    Last Post: 07-18-2014, 08:27 PM
  4. New resonant converters controllers.
    By borysgo2 in forum diysmps
    Replies: 0
    Last Post: 06-30-2014, 07:17 AM
  5. LLC Resonant Converter
    By lupusaudio in forum diysmps
    Replies: 46
    Last Post: 02-21-2014, 07:16 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •