Page 4 of 5 FirstFirst ... 2345 LastLast
Results 31 to 40 of 41

Thread: Cheapest PRINTED CIRCUIT BOARDS starting with 0,0375 Euro / cm2.

  1. #31
    Cheapest-tinned-printed-circuit-boards on FR4 support.


  2. #32
    Cheapest CEM3 pcb board ( adaptor of SOIC package with 0,15 mm traces )
    Tinning is FREE.


  3. #33
    Test boards (prototype printed boards) starting with 1 Euro / pce ( as the one below presented)


  4. #34
    Cheapest PRINTED-CIRCUIT-BOARDS, with FREE silkscreen (components mask)
    TINNING - it is offered as BONUS (for single and double layer boards, but for the ones WITHOUT ground plane)


  5. #35
    Cheapest DOUBLE LAYER printed circuit boards, on FR support with FREE tinning and FREE silkscreen (components mask)
    The DRILLING is also FREE.

    Below can be seen the TOP layer.

  6. #36
    Cheapest_PCB's ( printer-circuit-boards) ,on CEM3 professional support
    Free = DRILLING
    Professional TINNING , min. 1% Silver

  7. #37
    Cheapest - SILVERED - printed-circuit-boards-PCB's

  8. #38
    Cheapest-printed-circuit-boards

  9. #39
    .... Silvio's Avatar
    Join Date
    Apr 2015
    Location
    Malta
    Posts
    659
    Blog Entries
    9
    Very nice work and seems a good job. I have some questions for you.

    1) Can you produce PCB with PDF file? It will also contain silk screen and perhaps solder screen too.
    2) Can you produce SMD traces which are 0.2mm or 0.3mm thick?
    3) If I will need a prototype board the size of A4 paper or a little smaller, is it possible to order only one first?
    4) If double sided PCB does it contain vias with sleeve?

    Regards Silvio

  10. #40
    Hi Silvio,

    1. Yes. About " solder screen " maybe you are talking about soldermask. The soldermask has very low inquiries , even I ca do it.
    2. Yes
    3. A4 and bigger size it is possible, but please note that if you have more pcb's on A4 can not be " panelized" . The best is to be manufactured piece by piece, in order the have best quality of boards.
    4. No. For double side boards you will make the vias connection. For double side are required .brd ( Eagle files)

    I hope that may answers are very clear for you.

    Regards from Romania,

    Mihai



    Quote Originally Posted by Silvio View Post
    Very nice work and seems a good job. I have some questions for you.

    1) Can you produce PCB with PDF file? It will also contain silk screen and perhaps solder screen too.
    2) Can you produce SMD traces which are 0.2mm or 0.3mm thick?
    3) If I will need a prototype board the size of A4 paper or a little smaller, is it possible to order only one first?
    4) If double sided PCB does it contain vias with sleeve?

    Regards Silvio

Similar Threads

  1. What Could these I.C's be on this Circuit Board
    By Musgatz in forum Power Supplies
    Replies: 1
    Last Post: 11-16-2014, 07:10 PM
  2. SMPS AC to AC circuit
    By parvezsh in forum diysmps
    Replies: 1
    Last Post: 07-27-2013, 03:28 AM
  3. Replies: 8
    Last Post: 05-12-2013, 11:16 AM
  4. Replies: 9
    Last Post: 04-08-2013, 12:03 PM
  5. Loudness control - circuit!
    By radio in forum Pre Amps
    Replies: 7
    Last Post: 09-29-2012, 06:53 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •