Page 7 of 7 FirstFirst ... 567
Results 61 to 65 of 65

Thread: Audio smps 700w (IR2153)

  1. #61
    .... Silvio's Avatar
    Join Date
    Apr 2015
    Location
    Malta
    Posts
    555
    Blog Entries
    9
    @ Steppler

    Some more considerations

    1) input soft start missing+ bridging triac or relay missing
    2) input fuse missing
    3) safety ground capacitors missing 2 X 2.2nF X1KV
    4) grounding of the negative output terminal missing
    5) 1uF capacitor in parallel with output capacitor missing
    6) Grounding of the SMPS is non existent.

    If something happens and the primary of the transformer shorts out with the secondary you will see God prematurely.

    Regards Silvio

  2. #62
    @ Silvio

    This is input power board:

    ipw.jpg

    Among other things include softstart. 2s delay relay bridged resistors 40ohm 20W.

    Fuse to rear panel.

  3. #63
    .... Silvio's Avatar
    Join Date
    Apr 2015
    Location
    Malta
    Posts
    555
    Blog Entries
    9
    @Steppler
    That is much better. You showed a very basic schematic at first with a lot of things missing in it. By the way the pcbs you are making are very nice and looking professional.

    One other thing you should add is a 4.7nF capacitor from the high voltage ground to the negative ground of the secondary plus another capacitor 4.7nF from the negative of the secondary side to earth ground, this will protect both for EMI and also in the event of a short in the transformer windings (primary to secondary) it will find a path to earth ground and will trip the earth leak circuit breaker in the grid. One other choice is to ground the secondary negative terminal to chassis. If you have a double winding of say 30-0-30 then ground the center ground to earth ground. Take a look at my PDF file it can be downloaded on page 2 post #13. There I have a ground path which connects to chassis via the stand off pillars. Taking a general look you will see these capacitors I am mentioning, they are ceramic caps rated at 1kv.

    Did you get rid of the stray voltage?

    Regards Silvio

  4. #64
    I changed the transistors to IRF740, I added the snubber. Result? .... 90V !!!!

    I disconnected experimentally output coils and 2 capacitors ..... increase to 95V.

    And transformer is very hot.

    I will try to add ground capacitors.

    The experiment continues ........ my name is Don Quijote ......

  5. #65
    .... Silvio's Avatar
    Join Date
    Apr 2015
    Location
    Malta
    Posts
    555
    Blog Entries
    9
    @ Steppler
    Did you wind the transformer yourself?

    This is very odd Iwound a lot of transformers and this issue never happened to me. As I said before without a scope you are blindfolded.

    The transformer getting very hot is not a good sign and it could be that something may be wrong with it. (There should be no gap in the center leg of the core for this topology (Half bridge) Try to change the IR2153 and see that it is genuine.
    Please check if the output diodes are in the right orientation as I am suspecting that you are having a voltage doubler effect.
    It could be also the case that the windings are in series aiding and doubling the voltage somehow. I am trying to figure out what may be wrong and these are only assumptions. The circuit is very basic and has been built by a lot of people but these mishaps have not been encountered before apart of a faulty chip or something that I mentioned before.

    Put a series 100w Lamp with your input wiring. You can attach it instead of the fuse. This will help in the event of something is wrong. The bulb should light up briefly and extinguish again on start up due to charging the main bulk and secondary caps. The filament should show no signs of glowing during operation of the smps without load.

    I suggest that you take a look at my Youtube video ( Winding small transformers for SMPS) This will help you out for a good safety transformer build Don Quijote LOL.

    Link https://www.youtube.com/watch?v=_K3ixhcTYFg&t=1s

    regards Silvio.

Similar Threads

  1. Replies: 18
    Last Post: 01-23-2018, 10:43 PM
  2. 700W AMPLİFİER!
    By Sierra in forum Class AB
    Replies: 44
    Last Post: 07-21-2017, 08:14 AM
  3. Another IR2153 smps
    By borysgo2 in forum diysmps
    Replies: 2
    Last Post: 04-29-2017, 10:07 AM
  4. monoblock 700W rms/2Ω
    By ultra in forum Car Audio
    Replies: 9
    Last Post: 05-29-2013, 08:06 PM
  5. Building my first AC/DC 700w SMPS
    By Adonix in forum diysmps
    Replies: 4
    Last Post: 07-20-2011, 09:24 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •