diysmps - Powered by vBulletin
  • Register
  • Help
  • Home
  • Forum
  • Blogs
  • What's New?
  • Please read first <---- SMPS Warnings ---->
  • Advanced Search
  • Home
  • Home
  • diysmps
  1. If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

  • Recent Blog Posts

    Raza

    Calculation programs for transformers and inductors

    Raza 12-22-2019 11:26 PM
    d52perry

    smps flyback controller ic

    I am a nub is smps and just completed my first breadboard isolated smps with 24 volt input. I used the SG6848D controller from Ebay. Anyone has any suggestions for a better IC.
    Just some details...

    d52perry 12-15-2019 06:34 AM
    Faker

    Current Transfromer T1 Design

    Does anyone know the picture of the transformers windings design?
    Thanks

    Faker 11-28-2019 03:18 PM
    Faker

    Current Transfromer T1 Design

    Does anyone know the picture of the transformers wingdings design?
    Thanks

    Faker 11-28-2019 03:17 PM
    Faker

    Current Transfromer Design T2

    Does anyone know the picture of the transformers wingdings design?
    Thanks

    Faker 11-28-2019 03:17 PM

  • Recent Forum Posts

    Cortez

    Cooktop SMPS repair

    Ehh, strange yesterday evening I get back to this project but now everything was stable...
    There was't any turning down or instability. I even tried

    Cortez 01-17-2020, 06:57 AM Go to last post
    Cortez

    Cooktop SMPS repair

    Hi!

    I'm trying to repait a SMPS in an induction cooktop hope it's not a problem that only the repairment is DIY... :
    I attached

    Cortez 01-16-2020, 09:39 AM Go to last post
    Dr pepper

    CRT oscilloscope power supply which topology.

    I need to power a 'scope project.
    I have either 5v (preferably) or 12v source, and I need +12v, +300v, +400v, -200v, -300v and 6.3v (ac filament)

    Dr pepper 01-13-2020, 11:05 AM Go to last post
    hesamavr

    UC3842/3 Compensation Feedback

    Hi,

    I want to design a Flyback, no problem with the transformer, Clamp .. etc. Now I want to design the feedback circuit using a TL431

    hesamavr 01-10-2020, 10:38 AM Go to last post
    hesamavr

    A Flyback SMPS Design using the Flyback-6200 software

    Hello,

    I use Flyback-6200 software. I can design the transformer and RCD clamp with no problem. However, I stuck in designing the Feedback

    hesamavr 01-06-2020, 06:55 PM Go to last post
    hesamavr

    Adjustable switching power supply using LM2576

    Thank you very much. I will do that with a DC load.

    hesamavr 01-04-2020, 10:24 AM Go to last post
    Silvio

    Adjustable switching power supply using LM2576

    @Hesamavr

    This looks like a very nice project and the smps seems very stable and looks that it works fine. However if it had to be capable

    Silvio 01-04-2020, 09:10 AM Go to last post
    hesamavr

    Adjustable switching power supply using LM2576

    Hello,

    Please consider my work. Looking for suggestion/comment to make it better probably

    hesamavr 01-03-2020, 09:38 PM Go to last post
    hesamavr

    Calculation programs for transformers and inductors

    I have the same problem, downloaded 7100, but it doe not run on my PC. Even I tried to run by compatibility mode, no success. W10-x64

    hesamavr 01-03-2020, 08:56 PM Go to last post
    Silvio

    1000w smps based on LUDO3232

    You may probably having a ground loop. Make a star ground on the amplifier chassis and ground all your ground points to it. That is the preamp the the

    Silvio 01-02-2020, 07:41 AM Go to last post

  • diysmps

    There is no content in this section

    • Contact Us
    • diysmps
    • Archive
    • Top
    All times are GMT. The time now is 02:54 AM.
    Powered by vBulletin® Version 4.2.5
    Copyright © 2020 vBulletin Solutions Inc. All rights reserved.
    www.diysmps.com