Search:

Type: Posts; User: Silvio

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Try to change the control chip or...

    Try to change the control chip or mosfet/transistor controlling it. Check for broken winding in the transformer primary. Check also for faulty capacitors and high value startup resistor.

    Please...
  2. Replies
    4
    Views
    76

    @ mihaiu16 I have seen the datasheets of the...

    @ mihaiu16

    I have seen the datasheets of the opto drivers and transistors. The output current of the optocouplers are a little bit on the low side compared to the IR2110 one being of a maximum of...
  3. Replies
    4
    Views
    76

    You can follow the tread of LUDO 3232 for the...

    You can follow the tread of LUDO 3232 for the 1000w smps using an ETD49 transformer. You can find everything you need including the pcb in pdf and also gerber files. This smps uses sg3525 and...
  4. @Hesamavr This looks like a very nice project...

    @Hesamavr

    This looks like a very nice project and the smps seems very stable and looks that it works fine. However if it had to be capable of delivering around 3 Amps of current it will be more...
  5. Replies
    457
    Views
    102,463

    Sticky: You may probably having a ground loop. Make a...

    You may probably having a ground loop. Make a star ground on the amplifier chassis and ground all your ground points to it. That is the preamp the the power supply ground and the amplifier ground. ...
  6. Thread: EER43 Windings

    by Silvio
    Replies
    5
    Views
    432

    7191 Here is my idea for you. I just noticed...

    7191

    Here is my idea for you. I just noticed I made a small mistake the output voltage should read 16v and not 50v I was considering 50 Amperes not volts when I wrote 50v.
  7. Thread: EER43 Windings

    by Silvio
    Replies
    5
    Views
    432

    @SMLinear. Well I gave things another taught...

    @SMLinear.

    Well I gave things another taught and you might use two of your EER43 cores. These cores can readily supply more than 600w each at 20Khz. It is important that they be of the same...
  8. Thread: EER43 Windings

    by Silvio
    Replies
    5
    Views
    432

    Hello SMLinear, I am not sure from your post...

    Hello SMLinear,

    I am not sure from your post if you have ever built a SMPS before, I can see you are in for quite a task especially with the current involved in your PS. Having 12v@ 100A at the...
  9. Replies
    3
    Views
    308

    I took a look at the data sheet and yes in fact...

    I took a look at the data sheet and yes in fact you should be having around 70khz. You should try to measure frequency during load as due to the green mode operation at low power consumption the...
  10. Replies
    3
    Views
    308

    Can you post a schematic of the flyback...

    Can you post a schematic of the flyback converter?
    Tell us also the frequency of operation and details of the trafo and windings.
  11. Replies
    6
    Views
    505

    I think you are referring for the snubber across...

    I think you are referring for the snubber across the primary winding. This is there to suppress any spikes generated during switch off of every cycle. Through my experience When a transformer does...
  12. Replies
    6
    Views
    505

    At the current of 20A these effects will surely...

    At the current of 20A these effects will surely come out and that is the reason of the extreme heat. I suggest you wrap 4 wires at a time and make 6 bundles. If you have a copper sheet it will be...
  13. Thread: SMPS with PFC

    by Silvio
    Replies
    45
    Views
    13,575

    I guess you want to check the schematic for any...

    I guess you want to check the schematic for any errors correct? If that is so please post a larger image of the schematic as it is too small to see it
  14. Replies
    6
    Views
    505

    The wire for secondary with 22 wires 0.55mm can...

    The wire for secondary with 22 wires 0.55mm can surely carry the 20 amps needed. I am assuming that the winding get hot during a load of 20 amps. I do not know if you want this smps to work 100%...
  15. This is a two switch converter to my believe it...

    This is a two switch converter to my believe it is very immune to shoot trough. Your problem is very odd. It would be of much help if you could post some oscilloscope shots at least at idle. without...
  16. Replies
    457
    Views
    102,463

    Sticky: To check the dead time you need to take out the...

    To check the dead time you need to take out the cursors and put the waves on top of each other. You will notice that one wave has a shorter pulse width than the other. You need to measure that...
  17. Replies
    457
    Views
    102,463

    Sticky: @ Marshall. The wave forms look good I guess...

    @ Marshall. The wave forms look good I guess these are the low and high side being read together.
  18. @ Kees54, Try this Resonant smps design it may...

    @ Kees54, Try this Resonant smps design it may help you out. This is only designed for smps up to 700w

    Link ...
  19. Have you tried Elektrotanya? Try this link ...

    Have you tried Elektrotanya?

    Try this link ...
  20. [QUOTE=nhatspkt;16244]Can you give me some advice...

    [QUOTE=nhatspkt;16244]Can you give me some advice how to calculate flyback tranformer and select Bmax, D ?[/LinQUOTE]

    Here is some software that you can download and this will calculate...
  21. Replies
    1
    Views
    300

    Have you tried a larger output capacitor? For...

    Have you tried a larger output capacitor? For the output you need to put a light load for the output voltage to settle quicker.
  22. From what I am assuming is that not everybody has...

    From what I am assuming is that not everybody has the means of making a gap in a standard non gap core. From what I am thinking is that he is preferring to use a standard gapped core with the...
  23. Replies
    457
    Views
    102,463

    Sticky: Here you have a link and you find all the details...

    Here you have a link and you find all the details you want. If you want a lower voltage other than 12v just change the zener diode to the required voltage.
    ...
  24. So sorry I did not notice you already posted them...

    So sorry I did not notice you already posted them :D :D
  25. Hi Stewin could you post a PDF file so that we...

    Hi Stewin could you post a PDF file so that we have a more clear schematic and pcb layout?

    Thanks and regards Silvio
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4